| DS-5654A | DS-5652A | DS-5634A | DS-5632A | DS-5624A | DS-5622A | DS-5614A | DS-5612A |
---|
Frequency bandwidth (-3dB) | 500MHz | 350MHz | 200MHz | 100MHz |
Rise time
(Representative values) | 750ps | 1ns | 1.75ns | 3.5ns |
Number of input channels | 4 | 2 | 4 | 2 | 4 | 2 | 4 | 2 |
Maximum sampling speed | 2GS/s (when channels are coupled), 1GS/s (when all channels are used) |
Equivalent sampling speed | 100GS/s |
Peak detection resolution | 1ns |
Averaging function | 2 to 65536 times (power of 2 steps) |
Averaging
Count display function | Display the number of executions on the screen. |
Memory length | 5M points/ch (when 2 channels are coupled), 2.5M points/ch (all channels) |
Vertical resolution | 8 bits (when high resolution arithmetic is enabled: up to 12 bits) |
Vertical resolution display function | Display the number of resolution bits |
Input voltage range | 2mV/div ~ 10V/div(1MΩ)
2mV/div ~ 2V/div(50Ω) |
Offset voltage | 2mV/div ~ 50mV/div : ±1V, 50.2mV/div ~ 500mV/div : ±10V, 502mV/div ~ 10V/div : ±100V |
DC gain accuracy | ±(1.5% +0.5% full-scale) |
Maximum input voltage | ±400 VpeakI (1MΩ), 5 Vrms(50Ω) |
Bandwidth limit filter | Analog type:100MHz, 20MHz, 2MHz, 200kHz | Analog type:20MHz, 2MHz, 200kHz |
Digital type: Choose either LPF, HPF, or SMA, channel independent |
Input coupling | GND, DC 1MΩ, AC1MΩ, DC50Ω |
Input impedance | 1MΩ±1% //16pF, 50Ω±1% |
Probe sense | Auto search:1:1, 10:1, 100:1, 1000:1
Manual setting:1:1, 5:1, 10:1, 20:1, 50:1, 100:1, 200:1, 500:1, 1000:1, 2000:1 |
Time axis range | 500ps/div ~ 50s/div | 1ns/div ~ 50s/div | 2ns/div ~ 50s/div | 5ns/div ~ 50s/div |
Standard probe | SS-101R (with standard number of channels) | SS-0130R (with standard number of channels) |
Roll mode | 50ms/div ~ 50s/div (100kS/s max) |
Clock accuracy | ±10 ppm |
Trigger function |
---|
Trigger function | Edge, Edge Alternate, Edge OR, Number of Pulses, Pulse Width, Period, Missing, TV, Pattern (OR, NOR, AND, NAND),
Serial (UART, SPI, I2C) |
TV trigger (standard)/
Line setting range selection/
Field selection | NTSC, PAL, Custom/up to 3000/1, 2, 4, 8 |
Pulse number trigger setting range | 1 to 9999 events |
Pulse width trigger time setting range | 15ns~50s |
Cycle trigger time setting range | 40ns~50s |
Missing (dropout)
Trigger time setting range | 50ns~50s |
Pattern trigger | OR, NOR, AND, NAND |
Trigger source/
State/
Threshold level | All channels/HIGH, LOW, Don’t Care/Independent setting for all channels |
Serial trigger UART | Trigger selection | START, STOP,Parity error, data pattern | Comparison data length | 5 to 8 bits |
---|
Bit rate | 1000bps~1Mbps
(Set in 100bps units) | Signal source | CH1~CH4, EXT
(2-channel device is CH1, CH2, EXT) |
---|
Serial trigger UART | Trigger selection | Data pattern | Comparison data length | 4 to 64 bits |
---|
CS selection | Positive logic/Negative logic,
Idle time specification when there is no CS | Signal source | CH1~CH4, EXT
(2-channel device is CH1, CH2, EXT) |
---|
* CH1 input is for SCK signal input only: up to 20MHz |
Serial trigger I2C | Trigger selection | START, STOP, RESTART, NACK,Data pattern | Comparison data length | 7-bit/10-bit address, 1 to 5 bytes,
EEPROM read, byte (shift comparison available) |
---|
Address mode | Choose from 7-bit/10-bit/EEPROM read | Signal source | CH1~CH4, EXT
(2-channel device is CH1, CH2, EXT) |
---|
Trigger source | All channels, EXT (±0.5V), EXT10 (±5.0V), line |
Trigger slope/
Coupling | Positive, negative/AC, DC, high frequency removal, low frequency removal, noise removal |
Display/Resolution |
---|
Display/Resolution | 7.5-inch color TFT LCD (touch screen)/VGA:640 × 480 pixels |
Display format | YT, XY, XY Trigger |
Vector connection | Sample point interpolation display, dot display |
Analog
persistence | Solid tone display, spectrum display |
Persistence
Display time | 100ms, 200ms, 500ms, 1s, 2s, 5s, 10s,Infinite |
Save internal waveform
(REF memory) | 5 waveforms |
Front panel settings save | Five settings can be saved in the internal memory or USB memory device |
AUTO SETUP function | Can be set to Enabled or Disabled |
Parameter measurement, cursor, zoom, math, replay |
---|
Parameter measurement | Maximum value, minimum value, peak value, RMS value, cycle RMS value, average value, cycle average value, top, base, top-base, rising overshoot, falling overshoot, rising time 20-80%, falling time 80-20%, rising time 10-90%, falling time 90-10%, frequency, cycle, number of pulses (positive), number of pulses (negative), pulse width (positive), pulse width (negative), duty ratio, integral, skew (positive/negative), skew @ level |
Number of simultaneous measurements/
Statistical values display | Maximum 4 parameters/maximum value, minimum value, number of measurements |
Logging items, output destination | Time, parameter measurement results (conditions A, B, C, and D), Pass/Fail judgment results
When recording: Pop-up screen, internal memory (up to 86,400), after recording: USB memory device |
Pass/Fail | Judgment mode: parameter judgment or mask determination, judgment result: USB save, BEEP sound,
pulse output, logging
Page search function: select Pass or Fail, search forward or backward |
Cursor | Time, Amplitude, Time & Amplitude, Value at Cursor |
Zoom | Press the Zoom button on the front panel to display the magnified waveform in a different grid |
Math function | Addition, subtraction, multiplication, differentiation, integration, FFT (up to 8k points, rectangular, Hanning, flat top window function)
Double operation by either differential, integral, or FFT from the result of either addition, subtraction, or multiplication (9 patterns) |
Rescale/unit conversion | a * x + b (x: input voltage, a, b: user-defined)/volt, ampere, watt, °C, no display |
Replay | Automatic waveform recording, up to 2048 waveforms can be saved and replayed |
Frequency counter | 6-digit |
Interface | USB 2.0HS compatible (device, host), LAN (100Base-TX),
GPIB (factory option DS-576), AUX interface (connector for external option) |
AUX OUT | Trigger output and pass/fail judgment output can be switched |
Waveform data save | Save to USB memory device with binary, ASCII, Mathcad, arithmetic (ASCII), and arithmetic (Mathcad) |
Hard copy output | Save the image to a USB memory device in TIFF, BMP, or PNG (Transparent) format
or output to a PictBridge® -compatible printer |
Calibration signal output | Square wave 1kHz, 3Vp-p |
Power supply/power consumption | AC100V ~ 240V(50Hz / 603Hz), AC100V ~ 120V(400Hz) / 95VA max(60W max) |
Dimensions/Body weight | Approx. 330Wx190Hx124D mm/Approx. 3.7kg |
Environmental conditions |
---|
Performance warranty temperature | 10 ~ 35℃ |
Operating temperature/humidity/altitude | Temperature 0 to 40°C/Humidity 5 to 80% RH ≤ 30°C (no condensation),
55% RH or less 40°C (no condensation)/Altitude 2000m or less |
Standard Accessories |
---|
Probes (one for each channel), power cord (1), front panel cover (1), manual (CD-ROM) (1), user’s guide (1) |
Option |
---|
AUX IO CH1/CH2 output
DS-577
(Factory option) | AUX IO1: Output CH1 input signal with offset voltage added, AUX IO2: Output CH2 input signal with offset voltage added |
AUX IO CH1 output
DS-578
(Factory option) | Aux IO1: Output CH1 input signal with offset voltage added |
GPIB interface
DS-576
(Factory option) | GPIB: IEEE488.2 |
Probe power supply
DS-579 | IWATSU ELECTRIC active probe power supply 2 Series |