IWATSU DS-5600A Máy hiện sóng kĩ thuật số

Name: IWATSU DS-5600A Máy hiện sóng kĩ thuật số - Nihon Denkei Vietnam
SKU: DS-5600A
Availability: InStock

máy hiện sóng kĩ thuật số IWATSU DS-5600A series

Loại: Máy hiện sóng

Hãng sản xuất: IWATSU

Liên hệ

Máy hiện sóng IWATSU DS-5600A series có độ phân giải cao. Màn hình lớn 15,6 inchFULL HD

Liên hệ

Tư vấn Zalo

1. Đặc điểm của máy hiện sóng kĩ thuật số IWATSU DS-5600A series

Vận hành trực quan Bảng điều khiển cảm ứng & nút/núm & chuột
Lên đến 8CH
Độ phân giải cao 12 bit (tương đương 16 bit ở chế độ phân giải cao)
Độ dài bộ nhớ tối đa 120M điểm theo tiêu chuẩn
Truyền dữ liệu tốc độ cao nhanh hơn 15 lần so với trước đây
Chức năng cơ bản mở rộng, làm cho nó dễ sử dụng hơn
Băng thông100~500MHz
Tối đa 2 GS/s 4/2 kênh
Lên tới 5 triệu điểm

2. Ứng dụng của máy hiện sóng kĩ thuật số IWATSU DS-5600A series

điện tử ,oto

	DS-5654A	DS-5652A	DS-5634A	DS-5632A	DS-5624A	DS-5622A	DS-5614A	DS-5612A
Frequency bandwidth (-3dB)	500MHz		350MHz		200MHz		100MHz
Rise time	750ps		1ns		1.75ns		3.5ns
(Representative values)
Number of input channels	4	2	4	2	4	2	4	2
Maximum sampling speed	2GS/s (when channels are coupled), 1GS/s (when all channels are used)
Equivalent sampling speed	100GS/s
Peak detection resolution	1ns
Averaging function	2 to 65536 times (power of 2 steps)
Averaging	Display the number of executions on the screen.
Count display function
Memory length	5M points/ch (when 2 channels are coupled), 2.5M points/ch (all channels)
Vertical resolution	8 bits (when high resolution arithmetic is enabled: up to 12 bits)
Vertical resolution display function	Display the number of resolution bits
Input voltage range	2mV/div ~ 10V/div(1MΩ)
	2mV/div ~ 2V/div(50Ω)
Offset voltage	2mV/div ~ 50mV/div : ±1V, 50.2mV/div ~ 500mV/div : ±10V, 502mV/div ~ 10V/div : ±100V
DC gain accuracy	±(1.5% +0.5% full-scale)
Maximum input voltage	±400 VpeakI (1MΩ), 5 Vrms(50Ω)
Bandwidth limit filter	Analog type:100MHz, 20MHz, 2MHz, 200kHz				Analog type:20MHz, 2MHz, 200kHz
	Digital type: Choose either LPF, HPF, or SMA, channel independent
Input coupling	GND, DC 1MΩ, AC1MΩ, DC50Ω
Input impedance	1MΩ±1% //16pF, 50Ω±1%
Probe sense	Auto search:1:1, 10:1, 100:1, 1000:1
	Manual setting:1:1, 5:1, 10:1, 20:1, 50:1, 100:1, 200:1, 500:1, 1000:1, 2000:1
Time axis range	500ps/div ~ 50s/div		1ns/div ~ 50s/div		2ns/div ~ 50s/div		5ns/div ~ 50s/div
Standard probe	SS-101R (with standard number of channels)				SS-0130R (with standard number of channels)
Roll mode	50ms/div ~ 50s/div (100kS/s max)
Clock accuracy	±10 ppm
Trigger function
Trigger function	Edge, Edge Alternate, Edge OR, Number of Pulses, Pulse Width, Period, Missing, TV, Pattern (OR, NOR, AND, NAND),
	Serial (UART, SPI, I2C)
TV trigger (standard)/	NTSC, PAL, Custom/up to 3000/1, 2, 4, 8
Line setting range selection/
Field selection
Pulse number trigger setting range	1 to 9999 events
Pulse width trigger time setting range	15ns~50s
Cycle trigger time setting range	40ns~50s
Missing (dropout)	50ns~50s
Trigger time setting range
Pattern trigger	OR, NOR, AND, NAND
Trigger source/	All channels/HIGH, LOW, Don’t Care/Independent setting for all channels
State/
Threshold level
Serial trigger UART	Trigger selection		START, STOP,Parity error, data pattern		Comparison data length		5 to 8 bits
	Bit rate		1000bps~１Mbps		Signal source		CH1~CH4, EXT
			(Set in 100bps units)				(2-channel device is CH1, CH2, EXT)
Serial trigger UART	Trigger selection		Data pattern		Comparison data length		4 to 64 bits
	CS selection		Positive logic/Negative logic,		Signal source		CH1~CH4, EXT
			Idle time specification when there is no CS				(2-channel device is CH1, CH2, EXT)
	* CH1 input is for SCK signal input only: up to 20MHz
Serial trigger I 2C	Trigger selection		START, STOP, RESTART, NACK,Data pattern		Comparison data length		7-bit/10-bit address, 1 to 5 bytes,
							EEPROM read, byte (shift comparison available)
	Address mode		Choose from 7-bit/10-bit/EEPROM read		Signal source		CH1~CH4, EXT
							(2-channel device is CH1, CH2, EXT)
Trigger source	All channels, EXT (±0.5V), EXT10 (±5.0V), line
Trigger slope/	Positive, negative/AC, DC, high frequency removal, low frequency removal, noise removal
Coupling
Display/Resolution
Display/Resolution	7.5-inch color TFT LCD (touch screen)/VGA:640 × 480 pixels
Display format	YT, XY, XY Trigger
Vector connection	Sample point interpolation display, dot display
Analog	Solid tone display, spectrum display
persistence
Persistence	100ms, 200ms, 500ms, 1s, 2s, 5s, 10s,Infinite
Display time
Save internal waveform	5 waveforms
(REF memory)
Front panel settings save	Five settings can be saved in the internal memory or USB memory device
AUTO SETUP function	Can be set to Enabled or Disabled
Parameter measurement, cursor, zoom, math, replay
Parameter measurement	Maximum value, minimum value, peak value, RMS value, cycle RMS value, average value, cycle average value, top, base, top-base, rising overshoot, falling overshoot, rising time 20-80%, falling time 80-20%, rising time 10-90%, falling time 90-10%, frequency, cycle, number of pulses (positive), number of pulses (negative), pulse width (positive), pulse width (negative), duty ratio, integral, skew (positive/negative), skew @ level
Number of simultaneous measurements/	Maximum 4 parameters/maximum value, minimum value, number of measurements
Statistical values display
Logging items, output destination	Time, parameter measurement results (conditions A, B, C, and D), Pass/Fail judgment results
	When recording: Pop-up screen, internal memory (up to 86,400), after recording: USB memory device
Pass/Fail	Judgment mode: parameter judgment or mask determination, judgment result: USB save, BEEP sound,
	pulse output, logging
	Page search function: select Pass or Fail, search forward or backward
Cursor	Time, Amplitude, Time & Amplitude, Value at Cursor
Zoom	Press the Zoom button on the front panel to display the magnified waveform in a different grid
Math function	Addition, subtraction, multiplication, differentiation, integration, FFT (up to 8k points, rectangular, Hanning, flat top window function)
	Double operation by either differential, integral, or FFT from the result of either addition, subtraction, or multiplication (9 patterns)
Rescale/unit conversion	a * x + b (x: input voltage, a, b: user-defined)/volt, ampere, watt, °C, no display
Replay	Automatic waveform recording, up to 2048 waveforms can be saved and replayed
Frequency counter	6-digit
Interface	USB 2.0HS compatible (device, host), LAN (100Base-TX),
	GPIB (factory option DS-576), AUX interface (connector for external option)
AUX OUT	Trigger output and pass/fail judgment output can be switched
Waveform data save	Save to USB memory device with binary, ASCII, Mathcad, arithmetic (ASCII), and arithmetic (Mathcad)
Hard copy output	Save the image to a USB memory device in TIFF, BMP, or PNG (Transparent) format
	or output to a PictBridge® -compatible printer
Calibration signal output	Square wave 1kHz, 3Vp-p
Power supply/power consumption	AC100V ~ 240V(50Hz / 603Hz), AC100V ~ 120V(400Hz) / 95VA max(60W max)
Dimensions/Body weight	Approx. 330Wx190Hx124D mm/Approx. 3.7kg
Environmental conditions
Performance warranty temperature	10 ~ 35℃
Operating temperature/humidity/altitude	Temperature 0 to 40°C/Humidity 5 to 80% RH ≤ 30°C (no condensation),
	55% RH or less 40°C (no condensation)/Altitude 2000m or less
Standard Accessories
Probes (one for each channel), power cord (1), front panel cover (1), manual (CD-ROM) (1), user’s guide (1)

Phụ kiện 1

AUX IO CH1/CH2 output	AUX IO1: Output CH1 input signal with offset voltage added, AUX IO2: Output CH2 input signal with offset voltage added
DS-577
(Factory option)