IWATSU DS-5400A Series Máy hiện sóng kỹ thuật số
Loại:
Máy hiện sóng
Hãng sản xuất:
IWATSU
Liên hệ
Máy hiện sóng IWATSU DS-5400A có độ phân giải cao.
Liên hệ
1. Đặc điểm và tính năng của máy hiện sóng IWATSU DS-5400A
– Băng thông 100,200 MHz
– 2 GS/s 4/2 kênh
– 500k điểm
– IWATSU DS-5400A Series là phiên bản nâng cấp của DS-5400 với tốc độ lấy mẫu 2GS/s trên tất cả các model
– Hỗ trợ thuộc tính PNG cho đầu ra bản sao cứng
2. Ứng dụng của máy hiện sóng IWATSU DS-5400A
Máy hiện sóng kỹ thuật số IWATSU DS-5400A được ứng dụng rộng rãi trong sản xuất điện tử – viễn thông.
| DS-5424A | DS-5422A | DS-5414A | DS-5412A | |
| Frequency bandwidth (-3dB) | 200MHz | 100MHz | ||
| Rise time | 1.75ns | 3.5ns | ||
| (Representative values) | ||||
| Number of input channels | 4 | 2 | 4 | 2 |
| Maximum sampling speed | 2GS/s (when channels are coupled), 1GS/s (when all channels are used) | |||
| Equivalent sampling speed | 100GS/s | |||
| Peak detection resolution | 1ns | |||
| Averaging function | 2 to 256 times (power of 2 steps) | |||
| Memory length | 500k point/ch (all channels) | |||
| Vertical resolution | 8-bit | |||
| Input voltage range | 2mV/div ~ 10V/div | |||
| Offset voltage | 2mV/div ~ 50mV/div : ±1V, 50.2mV/div ~ 500mV/div : ±10V, 502mV/div ~ 10V/div : ±100V | |||
| Deskew | 0~500 ns | |||
| DC gain accuracy | ±(1.5% +0.5% full-scale) | |||
| Maximum input voltage | ±400 Vpk | |||
| Bandwidth limit filter | Analog type:20MHz,2MHz, 200kHz | |||
| Input coupling | GND, DC 1MΩ, AC1MΩ | |||
| Input impedance | 1 MΩ±1.0 % || 20 pF±2 pF(DC1MΩ) | |||
| Probe sense | Auto search:1:1, 10:1, 100:1, 1000:1 | |||
| Manual setting:1:1, 5:1, 10:1, 20:1, 50:1, 100:1, 200:1, 500:1, 1000:1, 2000:1 | ||||
| Time axis range | 2ns/div ~ 50s/div | 5ns/div ~ 50s/div | ||
| Standard probe | SS-0130R (with standard number of channels) | |||
| Roll mode | 50ms/div ~ 50s/div (100kS/s max) | |||
| Clock accuracy | ±10 ppm | |||
| Trigger function | ||||
| Trigger function | Edge, number of pulses, pulse width, period, missing, TV | |||
| Trigger mode | AUTO, NORMAL, SINGLE, STOP | |||
| TV trigger (standard)/Line setting range selection/ | NTSC, PAL, Custom/up to 3000/1, 2, 4, 8 | |||
| Field selection | ||||
| Pulse number trigger setting range | 1 to 9999 events | |||
| Pulse width trigger time setting range | 15ns~50s | |||
| Cycle trigger time setting range | 40ns~50s | |||
| Missing (dropout) | 50ns~50s | |||
| Trigger time setting range | ||||
| Trigger source | All channels, EXT (±0.5V), EXT10 (±5.0V), line | |||
| Trigger slope/Coupling | Positive, negative/AC, DC, high frequency removal, low frequency removal, noise removal | |||
| Display/Resolution | ||||
| Display/Resolution | 7.5-inch color TFT LCD (touch screen)/ VGA:640 x 480 pixels | |||
| Display format | YT, XY, XY Trigger | |||
| Vector connection | Sample point interpolation display, dot display | |||
| Analog persistence | Solid tone display, spectrum display | |||
| Persistence display time | 100ms, 200ms, 500ms, 1s, 2s, 5s, 10s,infinity | |||
| Save internal waveform | 5 waveforms | |||
| (REF memory) | ||||
| AUTO SETUP function | Can be set to Enabled or Disabled | |||
| Front panel settings save | Five settings can be saved in the internal memory or USB memory device | |||
| Parameter measurement, cursor, zoom, math, replay | ||||
| Parameter measurement | Maximum value, minimum value, peak value, RMS value, cycle RMS value, average value, cycle average value, top, base, top-base, rising overshoot, falling overshoot, rising time 20-80%, falling time 80-20%, rising time 10-90%, falling time 90-10%, frequency, cycle, number of pulses (positive), number of pulses (negative), | |||
| pulse width (positive), pulse width (negative), duty ratio, integral, skew (positive/negative), skew @ level | ||||
| Number of simultaneous measurements/statistical value display | Maximum 4 parameters/maximum value, minimum value, number of measurements | |||
| Cursor | Time, Amplitude, Time & Amplitude, Value at Cursor | |||
| Zoom | Press the Zoom button on the front panel to display the magnified waveform in a different grid | |||
| Math function | Addition, subtraction, multiplication, FFT | |||
| (up to 8k points, rectangular, Hanning, flat top window function) | ||||
| Rescale/unit conversion | a * x + b (x: input voltage, a, b: user-defined)/volt, ampere, watt, °C, no display | |||
| Replay | Automatic waveform recording, up to 1024 waveforms can be saved and replayed | |||
| Frequency counter | 6-digit | |||
| Interface | USB 2.0HS support (device, host), GPIB (factory option DS-576) | |||
| AUX interface | Connector for external option | |||
| Waveform data save | Save to USB memory device with binary, ASCII, Mathcad, arithmetic (ASCII), and arithmetic (Mathcad) | |||
| Hard copy output | Save the image to a USB memory device in TIFF, BMP, or PNG (Transparent) format | |||
| or output to a PictBridge® -compatible printer | ||||
| Calibration signal output | Square wave 1kHz, 3Vp-p | |||
| Power supply/power consumption | AC100~240Vrms(50/60Hz), AC100V~120V(400Hz) / 95VA(60W)max | |||
| Dimensions/Body weight | Approx. 330Wx190Hx124D mm/Approx. 3.7kg | |||
| Environmental conditions | ||||
| Performance warranty temperature | 10 ~ 35℃ | |||
| Operating temperature/humidity/altitude | Temperature 0 to 40°C/Humidity 5 to 80% RH ≤ 30°C (no condensation), | |||
| 55% RH or less 40°C (no condensation)/Altitude 2000m or less | ||||
| Standard Accessories | ||||
| Probes (one for each channel), power cord (1), front panel cover (1), manual (CD-ROM) (1), user’s guide (1) | ||||
| Option | ||||
| GPIB interface | GPIB: IEEE488.2 | |||
| DS-576 | ||||
| (Factory option) | ||||
| Probe power supply | IWATSU ELECTRIC active probe power supply 2 Series | |||
| DS-579 | ||||
| (Factory option) | ||||
